Header image

Overview

  • Compact design for easy hauling
  • Hydrostatic drive system
  • Commercial-quality engine
  • Easy to maintain

View Product Brochure

Features

Controls are easy to locate and use for operator comfort and productivity
    QuikTrak™ mowing (648M shown)QuikTrak™ mowing (648M shown)
    Control console (636M shown)Control console (636M shown)

     Controls are color coded and logically placed to make them easy for the operator to find and use:

    • Ground speed and direction are easily controlled by moving the two hand-lever hydrostatic drive controls forward or reverse.
      • Speeds are infinitely variable up to 8.2 mph (13.2 km/h) forward and 3.5 mph (5.6 km/h) reverse.
      • A positive neutral-lock position for the levers provides added safety.
    • Two stationary reference bars are provided for operator convenience and security.
      • Front reference bar is included to control speed and reduce fatigue from control lever operation.
      • Rear reference bar is included to make reverse operation easy while maintaining operator confidence.
    • Control levers return to neutral automatically for safety and convenience.
    • Separate choke is easy to locate and use.

      • It is obvious whether the choke is on or not.
      • Less adjustment is needed with the separate choke.
    Brake lever (engaged position)Brake lever (engaged position)
    Brake barBrake bar

    A tire brake is provided to give stability for parking the vehicle on hillsides and for transport; it should be engaged whenever the machine is not being used:

    • Brake must be engaged to start the machine, for added safety.
    • The tire brake bars are easily adjusted, if necessary, to maintain effective operation.
    Mower deck height-of-cut adjustment
    Mower deck lift handleMower deck lift handle
    Mower deck height-of-cut adjustmentMower deck height-of-cut adjustment

    An easy-to-use cutting height adjustment system allows the operator to adjust the mower deck cutting height with no tools and minimal effort:

    • Pull the lift lever back to the full-raised position.
    • Remove the tethered pin and place it at the desired cutting height.
    • Lower the lift lever; the lift lever and mower will stop at the desired cutting height.

     

    NOTE: Additional information on mower cutting height adjustment can be found in the mower deck section.

Compact design for easy hauling and excellent maneuverability
    Overhead view of 636M showing compact designOverhead view of 636M showing compact design
    Side view of 652M showing compact designSide view of 652M showing compact design

    From the operator's platform to the mower deck, John Deere QuikTrak™ Mowers have a compact and functional design:

    • The compact design allows the QuikTrak to operate in areas that a larger machine cannot. Often, this means the area can be mowed with a QuikTrak so it is not necessary to switch to a walk-behind mower.
    • With the compact design of QuikTrak Mowers, less space is required on a truck or trailer - which can mean there is room for an extra mower, resulting in saved time and money.
    Mowing a tight area with QuikTrak 636MMowing a tight area with QuikTrak 636M
    QuikTrak 652MQuikTrak 652M

    Whether mowing hills or on the level, trimming or mowing straight-away, the operator of a John Deere QuikTrak is able to affect the performance of the machine with their body:

    • The compact design of the QuikTrak allows the operator to use their body to help control the machine.
    • The innovative QuikTrak design puts the center of gravity at the operator's feet where body weight can be used to keep traction on the higher wheels to mow across slopes at higher speeds with greater control.
    • Faster ground speeds get work done quicker.
    • Less polar motion means quicker turns.
    • Better traction on slopes gives more control and increased productivity.
    • Superior stability gives more control and confidence when mowing hillsides.
    • Better visibility allows more-timely operator reaction to the terrain and obstructions.
    • Standing area is designed for improved range of motion to allow the operator more room to move and avoid obstacles.
    • Minimal operator-station obstruction allows safe and fast exits for clearing mower-path obstacles.
    • Operator area is designed for more comfort and less fatigue.
    Inset caster wheels (636M shown)Inset caster wheels (636M shown)
    Inset caster wheels (648M shown)Inset caster wheels (648M shown)

    John Deere QuikTraks are designed, tested, and manufactured to provide the best commercial mowing machines available:

    • Bull-nosed shape of front edge of mower deck allows caster wheels to be set back further, closer to the blades, for more effective ground following.
    • Compact design takes less space for mowing tighter areas and may allow room for an extra machine when hauling to the worksite.
Hydrostatic drive system is reliable and easy to use
    QuikTrak 636M mowingQuikTrak 636M mowing
    Hydrostatic pumpsHydrostatic pumps

    QuikTrak™ Mowers use a heavy-duty hydrostatic pump and wheel-motor drive system that gives reliable and consistent performance and long life:

    • Heavy-duty components stand up to the rigors of commercial use.
    • Individual pump and wheel motor design allows placement of these heavy components low in the vehicle for a low center of gravity and excellent hillside stability.

    Two Hydro-Gear™ 0.61-cu in. (10-cc) axial piston, variable displacement pumps provide hydraulic power to the wheel motors:

    • Pumps are linked to the hand-control levers to allow the operator to make speed and direction changes.
    • Rugged construction is ideal for high-performance commercial use.
    • Piston design gives efficient and consistent performance. 
    • A replaceable hydraulic filter helps ensure long life of the pumps and wheel motors.

    Two individual 12-cu in. (196.6-cc) piston wheel motors power the QuikTrak drive wheels. Their heavy-duty construction and super-efficient axial-piston design provides superior performance and seamless power to the wheels:

    • Integrated high-pressure shaft seal gives greater reliability.
    • Large bearings are designed with the capacity to carry heavier loads and give long life.
    Transmission oil filterTransmission oil filter
    Transmission fluid oil reservoirTransmission fluid oil reservoir

    A spin-on type replaceable hydraulic oil filter is conveniently located:

    • Extends life of transmission components by keeping oil clean
    • Easy-to-reach for easy and fast service

     

    A hydraulic fluid oil reservoir is located behind the leaning pad:

    • Located in a cleaner environment
    • Easy to access for inspection and service

    Transmission tow valves are provided on each hydrostatic pump to permit moving the QuikTrak without the engine running.

    Hydro-Gear is a trademark of Hydro-Gear Company.

Safety features are built-in to protect the operator and bystanders
    Operator trimming around tree with QuikTrak™ 652MOperator trimming around tree with QuikTrak™ 652M
    Mower discharge deflectorMower discharge deflector

    High-quality mower deflector directs cut clippings across the lawn for optimum appearance. Plastic material flexes if contacted to minimize damage.

    Operator controlsOperator controls
    Curb wheelsCurb wheels

    Key safety features of QuikTraks include:

    • Operator presence starting system

      • Operator on platform
      • Park brake engaged
      • Power take-off (PTO) disengaged
      • Control levers in neutral
      • Ignition key used to start the engine
    • A high-quality polyethylene mower-discharge deflector
      • Deflects if it strikes a solid obstruction, causing less damage
      • Returns to its original shape and function
    • Operator station designed to allow fast exit
    • Two large curb wheels
    • Easy to remove and replace shields
    • Stationary handles on either side of the traction controls for operator security
    • Control levers return to neutral when released
    Mower deck safety certification

    QuikTrak mower decks are evaluated by the manufacturer (John Deere Turf Care) and conform to ANSI B71.4 2004 safety certification specifications for commercial turf care equipment.

Commercial-quality engine is reliable and provides excellent performance and life
    EngineEngine
    Air cleaner accessAir cleaner access

    A commercial-quality 18.5-hp* (13.8-kW) at 3600 rpm air-cooled engine powers the QuikTrak™ Mower:

    • Overhead valve design
      • More horsepower and torque per cubic inch of displacement
      • Better fuel efficiency
    • Full-pressure lubrication with full-flow filter
      • Reduces engine wear by ensuring proper lubrication, even when operating on hillsides or uneven terrain
      • Helps keep oil clean for increased engine life
    • V-twin design
      • Fast starts
      • Smooth operation
    • Vertical shaft for efficient transfer of power to the transmission and mower
    • Standard dual-element, canister-type, dry replaceable heavy-duty air cleaner with secondary safety element
    • Fuel pump for consistent and reliable fuel supply to the carburetor
    • 50-state compliant engine, which complies with strict U.S. Environmental Protection Agency and California Air Resource Board emission standards, without loss of horsepower or torque
    • Air-cooled engine design for minimum maintenance and maximum reliability
    • Aluminum cylinder block
      • Effectively dissipates heat
      • Lightweight and strong construction
      • Extends engine life due to elimination of debilitating engine temperatures

    *The engine horsepower and torque information are provided by the engine manufacturer
    to be used for comparison purposes only. Actual operating horsepower and torque will be less.
    Refer to the engine manufacturer’s Web site for additional information.

    Engine oil-fill tube, filter, and drainEngine oil-fill tube, filter, and drain
    #

    Engine is equipped with a replaceable oil filter for longer engine life.

     

    Engine oil fill/check tube, oil filter, and oil drain are located close together for easy and convenient service.

36-in. (91-cm) fabricated mower deck is made from 7-gauge, 0.177-in. (4.6-mm) steel for reliability and performance
    QuikTrak™ mower deckQuikTrak™ mower deck
    Mower-deck reinforcementMower-deck reinforcement

    A well-designed mower deck can make the difference between just getting the job done and getting eye-catching results. The 7-gauge, 0.177-in. (4.6-mm) fabricated mower deck delivers a higher quality of cut in more diverse conditions to enhance mowing performance and the opportunity for profit for lawn-care businesses.

     

    Key features of the fabricated mower deck include: 

    • The mower deck is manufactured from 7-gauge, 0.177-in. (4.6-mm) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
    • A compact footprint delivers greater maneuverability when working in tight quarters.
    • A deep-deck design delivers excellent airflow so material is processed quickly and efficiently.
    • A powerful vacuum effect is created by the deck's unique air-flow design, which pulls more grass upright so that the blades can cut more evenly.

    Flexible mower-discharge deflectorFlexible mower-discharge deflector
    Caster wheelsCaster wheels

    The wide-discharge opening and raised deflector provide even clipping dispersal for an excellent finished appearance in all conditions.

     

    Caster wheels with flat-free tires contribute to a smooth, even cutting job:

    • Large, flat-free caster wheels carry the mower deck smoothly over the lawn.
    • Caster wheels are recessed to reduce the vehicle footprint and turning radius.
      • With the wheels less exposed, there is less chance they'll get snagged by immovable obstacles, thus improving maneuverability and reducing damage.

     

    Mower lift lever (raised position)Mower lift lever (raised position)
    Mower lift lever (minimum cut-height position)Mower lift lever (minimum cut-height position)

    The QuikTrak is equipped with a floating mower deck that offers several advantages over a fixed mower deck:

    • The lift lever allows the operator to raise the mower to the full-up position from the operator's station.
      • Convenient when transporting from one mowing area to another and when loading on a trailer or truck
      • Allows the operator to raise the mower over roots or other obstructions in the lawn on the fly
    • Lift-assist springs reduce the effort required to raise the mower deck.
    Cutting-height adjustmentCutting-height adjustment
    Easy-to-remove mower deck shieldsEasy-to-remove mower deck shields

    Mower cutting height can be set from 1.25 in. (3.2 cm) to 5 in. (12.7 cm) in 0.25-in. (0.64-cm) increments:

    • Pull the lift lever back to the full-raised position.
    • Remove the tethered pin and place it at the desired cutting height.
    • Lower the lift lever; the lift lever and mower will stop at the desired cutting height.

     

    Mower deck shields are easy to remove, with one knob, for access to the drive belt and other service points.

    Optional mulching attachment
    Optional mulching attachment and blades (similar design shown)Optional mulching attachment and blades (similar design shown)
    #

    Optional mulching attachment and special mulching blades are available:

    • This is a high-performance mulching attachment that includes formed steel baffles to control the material for superior performance.
    • The special mulching blades can also be used for side discharging, though overall cutting performance may be slightly less than with the standard blades.
Maintenance is simple and easy to reduce time and cost
    QuikTrak™ 648MQuikTrak™ 648M
    Open engine compartmentOpen engine compartment

    All service components are easy to access:

    • Servicing is simplified because of the open engine compartment.
    • All service and maintenance points are within easy reach.
    Dual-stage air cleanerDual-stage air cleaner
    Engine oil fill/check tube, oil filter, and oil drainEngine oil fill/check tube, oil filter, and oil drain

     Dual-stage air cleaner is easy to reach and easy to service:

    • Air cleaner has two filter elements.
    • Element is easy to access and easy to change.

    Engine oil service points are grouped together in easy-to-reach locations:

    • Reduces the time required to check and/or change the oil and filter.
    Leaning pad raised for service accessLeaning pad raised for service access
    Periodic service chartPeriodic service chart

    Simply raising the leaning pad exposes the hydrostatic oil reservoir, control linkage and other service areas.

     

    A periodic service chart is provided on the back of the hydraulic-oil reservoir under the leaning pad for convenience in keeping up on required service.

    Access to hydraulic pumpsAccess to hydraulic pumps
    Hydrostatic transmission control linkageHydrostatic transmission control linkage

    One large knob is used to remove service access shields on the mower deck, battery box, etc.:

    • Panels are easy to remove and install.

    Threaded ball and socket rod ends are used throughout the QuikTraks:

    • Provide precise control over a long period of time
    • Easily replaced when necessary
    Covenient access panelCovenient access panel
    Hydrostatic pump maintenance accessHydrostatic pump maintenance access

    Access to check and service the hydrostatic pumps and motors is readily available at the rear of the machine.

     

    Transmission tow valves enable moving the vehicle without the engine running.

    Battery boxBattery box
    Battery cover removed for service accessBattery cover removed for service access

    Secure battery box is provided to protect the battery, for reliable operation:

    • Cover is easily removed for servicing the battery.
    Front tow holeFront tow hole
    Rear tow holeRear tow hole

    Four tow holes, two at the front and two at the rear, are provided for safely towing or anchoring the vehicle.

Specifications

Engine

  • Model no. FS600V
  • Horsepower (gross) At 3,600 rpm, 18.5 hp
    13.8 kW
  • Displacement 36.8 cu in.
    603 cc
  • Cylinders Two, V-twin
  • Crankcase capacity With filter, 2.2 qt
    2.1 L
  • Oil filter Full flow, replaceable
  • Lubrication Full pressure
  • Cooling Forced air
  • Air cleaner Dry type, dual stage

Fuel system

  • Fuel type Gasoline
  • Fuel tank capacity 5.5 U.S. gal.
    20.8 L
  • Fuel tank switch/shut-off valve Yes

Electrical system

  • Charge system At 3,600 rpm, 15 amp
  • Battery voltage 12 V
  • Cold cranking amp 300 amp
  • Hour meter Digital
  • Operator presence starting system Yes

Drivetrain

  • Hydraulic pumps Hydro-Gear, 0.61 cu in.
    10 cc
  • Wheel motors Hydro-Gear HGM-P, 12 cu in.
    196 cc
  • Travel speed Forward
    Infinite, 0-8.2 mph
    Infinite, 0-13.2 km/hReverse
    Infinite, 0-3.5 mph
    Infinite, 0-5.6 km/h
  • Speed and direction control Twin hand-controlled levers
  • Hydraulic capacity With filter, dry, 5 qt
    4.7 L
  • Hydraulic oil cooler Yes
  • Filter Spin-on replaceable

Tires

  • Drive tires 18x8.5-10 Turf Master
  • Load rating 4 PR

Brakes

  • Dynamic braking Dual hand-controlled levers
  • Park brake Tire engagement
  • Park brake actuation Hand lever

PTO

  • Type Electro-magnetic with brake, 125 lb-ft
    169 Nm
  • Drive Dual B-section V-belt with Kevlar� cord

Mower decks

  • Available widths 36 in.
    91.4 cm
  • Deck construction Fabricated steel, floating mount system
  • Deck thickness 7 gauge
    0.18 in.
    4.6 mm
  • Discharge Side
  • Height-of-cut range Increments
    0.25 in.
    0.64 cm
    1.25-5 in.
    3.2-12.7 cm
  • Cutting width 36 in.
    91 cm

Blades

  • Length 18 in.
    45.7 cm
  • Thickness 0.203 in.
    0.516 cm
  • Tip speed 18,900 fpm
    5,761 m/min
  • Number Two

Wheels

  • Caster wheel type No-flat semi-pneumatic with sealed bearings
  • Caster wheel size 11x4-5

Dimensions

  • Length 62 in.
    157.5 cm
  • Width Deflector down, 49.5 in.
    125.7 cm
  • Height 46 in.
    117 cm
  • Weight With full fuel and oil, 731 lb
    332 kg

Additional information

  • Date collected 21-Apr-2017